Nanoleaf Light Panels

DIY Mounting Centre

Nanoleaf Light Panels

DIY Mounting Centre

Nanoleaf Light Panels

DIY Mounting Centre

Mounting on Drywall or Plaster

Recommended Installation

For drywall or plaster, we recommend using the double-sided adhesive tape that ships with your kit. Make sure to follow the instructions provided!

  1. Clean surface thoroughly with rubbing alcohol or soap and water.
  2. Let dry (or pat dry with a towel).
  3. Place mounting tape on panels.
  4. Place panels on wall.
  5. Press and hold for 60 seconds.

Need more double-sided tape?

Hack from the Community: Velcro Tape

Hide the pull tabs by using 3M’s velcro tape. We haven’t tested this installation and can’t guarantee it, but folks just like you speak highly of it. Make sure to follow 3M’s instructions for use carefully.

Want this?

Mounting on Drywall or Plaster

Recommended Installation

For drywall or plaster, we recommend using the double-sided adhesive tape that ships with your kit. Make sure to follow the instructions provided!

  1. Clean surface thoroughly with rubbing alcohol or soap and water.
  2. Let dry (or pat dry with a towel).
  3. Place mounting tape on panels.
  4. Place panels on wall.
  5. Press and hold for 60 seconds.

Need more double-sided tape?

Hack from the Community: Velcro Tape

Hide the pull tabs by using 3M’s velcro tape. We haven’t tested this installation and can’t guarantee it, but folks just like you speak highly of it. Make sure to follow 3M’s instructions for use carefully.

Want this?

Mounting on Drywall or Plaster

Recommended Installation

For drywall or plaster, we recommend using the double-sided adhesive tape that ships with your kit. Make sure to follow the instructions provided!

  1. Clean surface thoroughly with rubbing alcohol or soap and water.
  2. Let dry (or pat dry with a towel).
  3. Place mounting tape on panels.
  4. Place panels on wall.
  5. Press and hold for 60 seconds.

Need more double-sided tape?

Hack from the Community: Velcro Tape

Hide the pull tabs by using 3M’s velcro tape. We haven’t tested this installation and can’t guarantee it, but folks just like you speak highly of it. Make sure to follow 3M’s instructions for use carefully.

Want this?

Mounting on Ceilings or Angled Walls

Recommended Installation

Always use the Nanoleaf Screw Mount Kit or other secure mounting hardware when mounting your Nanoleaf Light Panels to a ceiling or wall that isn’t flat. Double-sided adhesive tape was not designed for these use cases.

Need a Nanoleaf Screw Mount Kit?

Mounting on Ceilings or Angled Walls

Recommended Installation

Always use the Nanoleaf Screw Mount Kit or other secure mounting hardware when mounting your Nanoleaf Light Panels to a ceiling or wall that isn’t flat. Double-sided adhesive tape was not designed for these use cases.

Need a Nanoleaf Screw Mount Kit?

Mounting on Ceilings or Angled Walls

Recommended Installation

Always use the Nanoleaf Screw Mount Kit or other secure mounting hardware when mounting your Nanoleaf Light Panels to a ceiling or wall that isn’t flat. Double-sided adhesive tape was not designed for these use cases.

Need a Nanoleaf Screw Mount Kit?

Mounting to Masonry or Concrete

Recommended Installation

The Nanoleaf Screw Mount Kit (or similar secure mounting hardware) is required for mounting your Nanoleaf Light Panels to porous surfaces such as masonry or concrete. You’ll also need masonry screws and likely a power drill and masonry bits. Or a friend with really big biceps! Make sure to wear safety goggles =)

Available at Amazon:

On the Nanoleaf Shop:

Many hardware stores will also rent power drills and drill bits if you’re only ever going to use these once.

Mounting to Masonry or Concrete

Recommended Installation

The Nanoleaf Screw Mount Kit (or similar secure mounting hardware) is required for mounting your Nanoleaf Light Panels to porous surfaces such as masonry or concrete. You’ll also need masonry screws and likely a power drill and masonry bits. Or a friend with really big biceps! Make sure to wear safety goggles =)

Available at Amazon:

On the Nanoleaf Shop:

Many hardware stores will also rent power drills and drill bits if you’re only ever going to use these once.

Mounting to Masonry or Concrete

Recommended Installation

The Nanoleaf Screw Mount Kit (or similar secure mounting hardware) is required for mounting your Nanoleaf Light Panels to porous surfaces such as masonry or concrete. You’ll also need masonry screws and likely a power drill and masonry bits. Or a friend with really big biceps! Make sure to wear safety goggles =)

Available at Amazon:

On the Nanoleaf Shop:

Many hardware stores will also rent power drills and drill bits if you’re only ever going to use these once.

Tabletop Mounting

A Nanoleaf Hack

Looking to mix it up a bit and create three dimensional shapes on a tabletop? All you’ll need is a pack of Nanoleaf Flex Linkers, and some re-usable putty! Check out our video on creating a light pyramid.

Tabletop Mounting

A Nanoleaf Hack

Looking to mix it up a bit and create three dimensional shapes on a tabletop? All you’ll need is a pack of Nanoleaf Flex Linkers, and some re-usable putty! Check out our video on creating a light pyramid.

Tabletop Mounting

A Nanoleaf Hack

Looking to mix it up a bit and create three dimensional shapes on a tabletop? All you’ll need is a pack of Nanoleaf Flex Linkers, and some re-usable putty! Check out our video on creating a light pyramid.

Mounting to Ferrous Metal

Hack from the Community: Dot Magnets

Want to mount your panels to a metal surface and easily reposition them? If a magnet will stick to it, the community has an a hack for you! Dot magnets with adhesive backing can be used for this installation. Peel and stick the magnetic dot to the reverse of your Nanoleaf Light Panels at each corner, then place on the metal surface. Always make sure to follow the manufacturer’s instructions, and make sure to get a dot magnet that will support the weight of the panels (look for extra-strength ferrite magnets).

This hack hasn’t been tested by us and isn’t endorsed by Nanoleaf =)

Mounting to Ferrous Metal

Hack from the Community: Dot Magnets

Want to mount your panels to a metal surface and easily reposition them? If a magnet will stick to it, the community has an a hack for you! Dot magnets with adhesive backing can be used for this installation. Peel and stick the magnetic dot to the reverse of your Nanoleaf Light Panels at each corner, then place on the metal surface. Always make sure to follow the manufacturer’s instructions, and make sure to get a dot magnet that will support the weight of the panels (look for extra-strength ferrite magnets).

This hack hasn’t been tested by us and isn’t endorsed by Nanoleaf =)

Mounting to Ferrous Metal

Hack from the Community: Dot Magnets

Want to mount your panels to a metal surface and easily reposition them? If a magnet will stick to it, the community has an a hack for you! Dot magnets with adhesive backing can be used for this installation. Peel and stick the magnetic dot to the reverse of your Nanoleaf Light Panels at each corner, then place on the metal surface. Always make sure to follow the manufacturer’s instructions, and make sure to get a dot magnet that will support the weight of the panels (look for extra-strength ferrite magnets).

This hack hasn’t been tested by us and isn’t endorsed by Nanoleaf =)

Full disclosure: Nanoleaf may earn commissions on sales when you click any of the Amazon links above to make a purchase. We donate these proceeds to the World Wildlife Fund during our annual Earth Week pledge in April.

Full disclosure: Nanoleaf may earn commissions on sales when you click any of the Amazon links above to make a purchase. We donate these proceeds to the World Wildlife Fund during our annual Earth Week pledge in April.

Full disclosure: Nanoleaf may earn commissions on sales when you click any of the Amazon links above to make a purchase. We donate these proceeds to the World Wildlife Fund during our annual Earth Week pledge in April.