製品体験を拡張するために設計されたローカルネットワークAPI。 サードパーティデバイスやサービスとセットアップを統合。ハードウェアのきめ細かい操作を実現。
Shapes User Manual
Mounting Your Shapes
取付面の準備
Nanoleaf Shapesは、屋内で、パネルの重量を支えることができる平らな面にのみ設置する必要があります。表面をきれいにして、ホコリや水分、油分のない状態にします(1.1)。付属の取付テープは、質感のある、ポップコーンや多孔質の表面(壁紙やレンガの壁など)や、質感のいかんを問わず天井での使用は推奨されていません。(1.2).
Prepare Your First Panel
セットアップの際に1つのパネルを開始パネルとして指定します。壁にパネルを取り付ける前に、必要なリンカーをすべて取り付けます。
Connect the Controller & PSU
コントローラーと電源を最初のパネルの利用可能なリンカーポートに接続します。PSUのもう一方の端を電源に接続し、パネルを接続する際に、セットアップがオンになっていて正しく接続されていることを確認してください。
How many PSUs do I need?
Each standard 42W PSU supports up to 22 Hexagon panels (2W per panel). Each Controller supports up to 500 Hexagon panels. Please check out our PSU Calculator for large installations.
Each standard 42W PSU supports up to 28 Triangle panels (1.5W per panel). Each Controller supports up to 500 Triangle panels. Please check out our PSU Calculator for large installations.
Each standard 42W PSU supports up to 77 Mini Triangle panels (0.54W per panel). Each Controller supports up to 500 Mini Triangle panels. Please check out our PSU Calculator for large installations.
PSU calculator電源計算機
42W: One (1) 42W Power Supply Unit comes with any Nanoleaf Shapes Starter Kit.
75W: For optimal performance, do not use both 42W and 75W Power Supplies in the same Nanoleaf setup.
パネルを取り付ける
Remove the protective liner from the tape and position your panel into place. Mount your panel by applying strong pressure to the center (this should be where the Mounting Plate is on the reverse side). Make sure to rub your fist in a circular motion for 30 seconds to avoid any falling panels.
Make sure to leave end of the tape sticking out. This will allow you to safely remove them later from the wall.
セットアップを完了する
次のパネルを壁に取り付ける前に、必要なリンカーをすべて取り付けます。続けて各パネルをリンクし、各パネルが点灯することを確認します。リンカーがリンカーポートに完全に固定されていることを確認してください。
Screw Mounting Your Panels on the Ceiling or Angled Surfaces
天井や角度のある面にパネルを取り付けたい場合、テープではなくてねじを使いきちんと固定してください。
- Mark up where your anchors will go. Position a Mounting Plate in place and mark up the 2 holes with a pencil.
- Install anchors (may need to drill a pilot hole).
- Fasten Mounting Plate to anchors with screws.
- Once secured, attach the panel to the Mounting Plate.
新しいテープを追加する場合
When you need to attach a replacement tape to your Mounting Plate, make sure the tape is placed between the two holes. Leave end of the tape sticking out. This will allow you to safely remove them later from the wall. Visit our shop for additional Mounting Tapes.
Shapesを取り外す必要がありますか?
そっと壁からパネルをはがします。取付プレートは、壁に取り付けたままになります。片手を取付プレートに置き、もう一方の手を使って壁に沿ってテープの端を引っ張ります。直角またはその他の角度で引っ張らないでください。壁を損傷する可能性があります。
Need more Mounting Tape? Get it here.
あなたの傑作に追加しましょう!
拡張パックでさらにクリエイティブに、セットアップを成長させましょう。
GET ONE TODAY