Một API mạng cục bộ được thiết kế để mở rộng trải nghiệm sản phẩm của bạn. Tích hợp hệ thống đèn của bạn với các thiết bị và dịch vụ của bên thứ ba và cho phép điều khiển phần cứng chi tiết hơn.
Table of Content
Lines User Manual
Gắn đèn Lines
Select a Product:
Lines 60 Degrees Lines 90 Degrees
Video tutorial for mounting
1
Chuẩn bị bề mặt
Nanoleaf Lines should only be installed indoors and on a flat surface that can support the weight of the Lines. Clean your surface to be free of dust, moisture and oil. The included Mounting Tape is NOT recommended for textured, porous surfaces (ie. wallpaper or brick walls), popcorn walls /ceilings, and mirrors. See detailed guide for ceiling installations here.
2
Xây dựng bố cục thiết kế
Design your layout on a table or the floor. Once you are happy with your design, secure your Lines 6090 Degrees with the 6090 Degree Connector Caps.
Note
the Controller Cap with buttons can be attached to any Connector!
3
Kết nối bộ cấp nguồn
Cắm vào nguồn điện để đảm bảo rằng Lines của bạn đã bật và hoạt động bình thường.
How many PSUs do I need?
Each standard 42W PSU supports up to 18 Lines 6090 Degrees (2W per line). You can connect up to 250 Lines in one layout to be controlled with a singular Controller Cap. Please check out our PSU Calculator for large installations.
PSU calculatorMáy tính toán Bộ cấp nguồn
42W: One (1) 42W Power Supply Unit comes with any Nanoleaf Lines Starter Kit.
4
Gắn đèn Lines
Grab a friend to help with mounting your layout (4.1). For the best results, mount your layout all at once. For larger designs, mount in sections; be sure to mount closed-loop layouts together (triangles, hexagons, etc.). Carefully lift up your Lines 6090 Degrees layout and peel off the backing of the Mounting Tape. Press each of the Mounting Connectors against the wall for 30 seconds to secure your layout to the wall (4.2)
Note
Need more Mounting Tape? Purchase more here
5
Lắp trên trần nhà
For a more secure installation, including for your ceiling instals, use the screw-mount solution (Screws not included).
Note
the screw mounting solution is still designed for SMOOTH surfaces/ceilings only.
Mount your Lines design to the ceiling first using the included Mounting Tape. Remove the light lines then carefully pull Mounting Connectors off to reveal the Mounting Plates which should be still adhered to the ceiling(5.1). Mark the screw holes (5.2) and then remove the mounting plate (5.3). See below how to safely remove Mounting Plates. Drill pilot holes and instal anchors. Please proceed with extra caution for hole alignment, large screw mount tolerance offset may lead to disruption of closed loop layout assemblies (5.4). Fasten Mounting Plate to anchors with screws (5.4). Once secured, attach the light lines and Mounting Connectors back onto the Mounting Plate.
Bạn cần tháo gỡ đèn Lines?
Gently snap off the Connector Caps, then gently remove the light lines from the Mounting Connectors (1). Carefully pull the Mounting Connectors away from the attached surface (2). The Mounting Plate will remain adhered to the wall. With one hand on the Mounting Plate, use your other hand to pull the end of the exposed tape along the wall until fully removed (3).
Note
Do NOT pull perpendicular from the wall or at any other angle, otherwise, you may damage your wall (2).
Mở rộng kiệt tác của bạn!
Thỏa sức sáng tạo và phát triển hệ thống đèn của bạn với Bộ mở rộng.
GET ONE TODAY
