Skylight User Manual

Setting up the Main Controller Panel

For Your Safety:

1. Before you start, turn off the power of your main circuit.
2. Plan out your layout. Align and mark the panels of your desired layout on the ceiling.

Mount the Main Controller Panel

• Turn the circuit power and the light switch off before you start.

• To open the Main Controller Panel(A):

  First

  Pull the clear tape on the panel.

  Second

  Insert a flat head screwdriver into one of the small notches along the seam. Slightly twist the screwdriver.

  

  

• Remove the L Shape Cover to reveal the terminal block for wiring.

  

• Remove the Ceiling Plate by unscrewing the Wing Nuts (C).

  

• If mounting with the Ceiling Plate, ensure that the wires are positioned through the hole of the plate with a suitable length visible

• Fasten the Ceiling Plate so that it is parallel to your desired panel alignment.

  

  

• The Main Controller Power Wires (L) attached to the Main Controller Panel (A) can be connected with junction box wires using the included Binding Posts (H).

  Black = Live wire

  White = Neutral wire

• Make sure the wires are secure and connected to the corresponding wires.

  

• Use the electric drill (Ø6mm) to break through the four knockout holes.

  

• Positioning the Main Controller Panel (A) at the desired ceiling location and hold it against the ceiling.

  

• Take a pencil and mark each screw hole on the ceiling.

  

• Now align and mount the Main Controller Panel (A) back to the Ceiling Plate.

• Make sure the wires have passed through the Ceiling Plate and that the Main Controller Panel (A) sits secure and flat on the plate.

• Secure the Ceiling Plate with the Wing Nuts (C).

  

  

• Using the provided anchors and screws, mount your Main Controller Panel in place with the four knockout holes in the corner of each panel.

• To mount the panel in place you can use:

  First Option: Drywall Anchors (F)

  Screw in the four Drywall Anchors (F) to the four spots you marked prior

  Second Option: Plaster Anchors (G)

  Drill a hole of 6mm (OD) then drive the Mounting Screw (E) into the Plaster Anchor (G)

  

  Different mounting hardware will be required for installation on structural wood, concrete, and porous masonry surfaces. The correct items are widely available at hardware and home improvement stores.

Connect Electrical Wiring

• Insert the ceiling wires into any of the slots on the terminal block. Use your finger or a screwdriver to push the clamps when inserting. Make sure the wires are secured in place such that it cannot be pulled out.

  Black = Live wire

  White = Neutral wire

• Remove any terminal block knockout holes as needed.

Setting up the Expansion Panels

Mount Expansion Panels

• Add an Expansion Panel (B) and position it next to the Main Controller Panel (A).

• Remove the knockout holes on all four corners, hold it against the ceiling and mark each screw holes with a pencil.

• For each Expansion Panel (B), repeat the steps for mounting found here.

  First Option: Drywall Anchors (F)

  Screw in the four Drywall Anchors (F) to the four spots you marked prior

  Second Option: Plaster Anchors (G)

  Drill a hole of 6mm (OD) then drive the Mounting Screw (E) into the Plaster Anchor (G)

Connect the Wires

• Thread the wires through the Grommet Cover to connect the Communication Linker (J) from the Main Controller Panel (A) to the Expansion Panel (B) through the linker slot.

• Attach the Power Wires (K) to the socket closest to the next expansion panel. Follow the embossed line and wire through the opening to the next panel where the Communication Linker is attached.

• Repeat this step for additional panels you add.

Power On Your Skylight

• Turn the circuit power back on and turn the light switch on to power the panels.

  

• Your new Skylight panels will now power on at low brightness. Once the boot-up process is complete, the panels will gradually shift to full brightness to indicate that the system is ready for pairing.

  

• Reinstall the L Shape Cover.